The Breitling Watch Source Forums

Breitling Watch Information Forums, Navitimer, Chronomat
 
It is currently Mon Sep 21, 2020 12:11 pm

All times are UTC - 8 hours




Post new topic Reply to topic  [ 10 posts ] 
Author Message
PostPosted: Wed Jan 16, 2008 11:41 am 
Offline
Breitling Newbie
Breitling Newbie

Joined: Tue Dec 25, 2007 5:47 pm
Posts: 7
Likes: 0 post
Liked in: 0 post
Location: Seattle/Eastside, WA
Something strange seems to be going on with my Evo and my Wolf Designs winder. The watch winds fine when I'm wearing it -- I've left it out of the winder (or the winder off) for many days, and as long as I wear it daily, it keeps on going with no problem. But it seems like the winder isn't doing its job properly. This morning I pulled my watch out of the winder after not having worn it for a few days, and it had stopped.

I have the winder set to "clockwise," which I was pretty sure is right for the movement in the Evo. Is that wrong? Any other ideas about what's going on?


Top
 Profile  
Reply with quote  
 Post subject: Winder problems
PostPosted: Wed Jan 16, 2008 2:57 pm 
Offline
Breitling Enthusiast
Breitling Enthusiast

Joined: Tue Jan 08, 2008 9:58 am
Posts: 86
Likes: 0 post
Liked in: 0 post
Location: Panhandle Florida
Which model do you have, the 1.5 or 2.0 version etc? It should have a light that intermittently flashes green when the system is operational. Are you using batteries or the cord?

_________________
Never deny anyone hope..........it may be all they have.


Top
 Profile  
Reply with quote  
 Post subject:
PostPosted: Wed Jan 16, 2008 3:18 pm 
Offline
Breitling Newbie
Breitling Newbie

Joined: Tue Dec 25, 2007 5:47 pm
Posts: 7
Likes: 0 post
Liked in: 0 post
Location: Seattle/Eastside, WA
Sorry, I should have been more specific. I have the 2.0 single winder. I'm using the AC adapter, and it the green light does blink. Depending on what I've been doing, I either use the "12" mode or the "on" mode.

I know that it does rotate the watch (I've seen it moving). However, I haven't watched it intently for a long period of time, and I'm not sure what the expected rotation pattern is, so I don't know if it's consistently rotating correctly.

It seems kind of hard to troubleshoot this, because there's no way to tell how much the watch has been wound (until it's so little that it stops completely)...


Top
 Profile  
Reply with quote  
 Post subject:
PostPosted: Wed Jan 16, 2008 6:52 pm 
Offline
Site Admin
Site Admin
User avatar

Joined: Tue Jan 09, 2007 3:40 pm
Posts: 3320
Likes: 120 posts
Liked in: 18 posts
Location: canada
It should be on option B, and set to "On". If your Chronomat Evo has been almost wound down and it is put in the winder if may not keep the watch wound, since it will not wind your watch up. You may want to try winding the watch all the way up and then sticking it in the winder to see how long that lasts.

_________________
BreitlingSource Admin
http://www.breitlingsource.com - http://blog.breitlingsource.com


Top
 Profile  
Reply with quote  
 Post subject:
PostPosted: Wed Jan 16, 2008 8:07 pm 
Offline
Breitling Newbie
Breitling Newbie

Joined: Tue Dec 25, 2007 5:47 pm
Posts: 7
Likes: 0 post
Liked in: 0 post
Location: Seattle/Eastside, WA
breitlingsource wrote:
It should be on option B, and set to "On".


I had it on B. However, it's somewhat confusing. On the Wolf website, the picture of the 2.0 actually shows arrows above each option for which way it turns. Mine doesn't have that, so all I have to go by is what the manual says. It says:

Quote:
...a clockwise direction- A setting, counter-clockwise direction- B setting, or a combination of both- C setting.


This implies that B is counter-clockwise. Right next to that, there's a diagram that says:

Quote:
A-Counter-clockwise
B-Clockwise
C-Both directions


That implies the opposite: that B is clockwise.

When I'm looking at the winder from the front, B makes the watch rotate counter-clockwise, A makes the watch rotate clockwise, and C does both. This seems to match the text, but not the diagram. I thought that my watch needed clockwise, which based on my observation and the text (but not the diagram, and not your instructions) would be A.

I have a feeling I'm missing something. What is going on?

Thanks for your help!


Top
 Profile  
Reply with quote  
 Post subject: Wolf winder
PostPosted: Thu Jan 17, 2008 8:52 am 
Offline
Breitling Enthusiast
Breitling Enthusiast

Joined: Tue Jan 08, 2008 9:58 am
Posts: 86
Likes: 0 post
Liked in: 0 post
Location: Panhandle Florida
You are correct. Option A will wind clockwise, B will wind counter-clockwise and C will alternate between both. I was going to ask you if the cover was latching fully but obviously if you have seen it winding it is functioning. I usually choose Option C (Steelfish winds both directions) with the 12 hour delay, only because I have been recently wearing the watch. Either way the rotation sequence should be as follows: winding clockwise for 20 min then counter-clockwise for 20 minutes followed by a 70 minute rest. This will continue for 7 hours and then the winder will remain dormant for 17 hours allowing the mainspring to release. Hopefully it is not dropping off after the first sequence of winding. I'm sure the last thing you have time for is sitting around watching a winder go through it's full program.

_________________
Never deny anyone hope..........it may be all they have.


Top
 Profile  
Reply with quote  
 Post subject:
PostPosted: Thu Jan 17, 2008 11:04 am 
Offline
Breitling Fanatic
Breitling Fanatic
User avatar

Joined: Wed Nov 14, 2007 7:19 am
Posts: 167
Likes: 0 post
Liked in: 0 post
Location: Texas
This may not help, but I read on another forum that someone had a winder problem (not sure of the brand) and placing a small book under one edge solved it. I think the winder was rotating too flat so the watch wasn't getting wound.

_________________
Life is too short to have a crappy watch.

:pcacborc:
:threequartslingclub:
Navitimer o1 LE
SuperOcean Steelfish
Bathys 100Fathoms Aquaculture
RXW MM20
RXW MM25
Seiko Sumo
Seiko Orange Monster
Movado series 800 diver
Thanks
Terry


Top
 Profile  
Reply with quote  
 Post subject:
PostPosted: Thu Jan 17, 2008 11:56 am 
Offline
Site Admin
Site Admin
User avatar

Joined: Tue Jan 09, 2007 3:40 pm
Posts: 3320
Likes: 120 posts
Liked in: 18 posts
Location: canada
I read the manual online and it said B was clockwise, so that's where I got that info for it - it might very well be wrong if they misprinted. If A is indeed clockwise, then that would explain the lack of winding. Have you tried just looking at the winder and seeing if A or B is clockwise? that would be the easiest.

Your watch does need the clockwise wind, so whichever mode gets you clockwise.. :mrgreen:

_________________
BreitlingSource Admin
http://www.breitlingsource.com - http://blog.breitlingsource.com


Top
 Profile  
Reply with quote  
 Post subject:
PostPosted: Sat Jan 19, 2008 10:47 pm 
Offline
Breitling Fanatic
Breitling Fanatic
User avatar

Joined: Sat Aug 18, 2007 6:37 pm
Posts: 442
Likes: 0 post
Liked in: 0 post
Location: Kansas City Mo.
On a side note (at least related to this post) does the SA wind in both directions?


Top
 Profile  
Reply with quote  
 Post subject:
PostPosted: Sun Jan 20, 2008 9:19 pm 
Offline
Breitling Fanatic
Breitling Fanatic

Joined: Sat Jul 21, 2007 5:07 pm
Posts: 340
Likes: 0 post
Liked in: 0 post
Location: Seoul, South Korea/Garden Grove, CA
the SA uses the same caliber 13 as the evo, so i assume it would also only wind in the clockwise direction.

jason

_________________
:threequartslingclub: chronomat evolution mop
:fulllingclub: bentley motors t black dial


Top
 Profile  
Reply with quote  

Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 10 posts ] 

All times are UTC - 8 hours


Who is online

Users browsing this forum: No registered users and 9 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
 


Powered by phpBB® Forum Software © phpBB Group