The Breitling Watch Source Forums
https://www.breitlingsource.com/phpBB2/

Would appreciate help with a steelfish
https://www.breitlingsource.com/phpBB2/viewtopic.php?f=1&t=67241		 Page 1 of 1
Author:  what7 [ Wed Jun 03, 2020 4:15 pm ]
Post subject:  Would appreciate help with a steelfish
Hi,
Hope everyone is well.
I have a chance at a steelfish at a great price locally.
He has box and papers etc.
After doing research i found out there are a lot of fakes.
Any help with authentication would be awesome
Thanks
Author:  jnelson3097 [ Wed Jun 03, 2020 6:51 pm ]
Post subject:  Re: Would appreciate help with a steelfish
Yeah, there are plenty of fakes. Can you post pictures of the watch you’re looking at buying?
Author:  Jhdscript [ Wed Jun 03, 2020 11:05 pm ]
Post subject:  Re: Would appreciate help with a steelfish
If you could post a picture about the movement too.
Author:  Driver8 [ Thu Jun 04, 2020 3:18 am ]
Post subject:  Re: Would appreciate help with a steelfish
what7 wrote:
Hi,
Hope everyone is well.
I have a chance at a steelfish at a great price locally.
He has box and papers etc.
After doing research i found out there are a lot of fakes.
Any help with authentication would be awesome
Thanks

As others have said, decent high quality pictures are the best bet as we have some great fake spotters on here, and the Steelfish was one of the first "good" fake Breitlings produced. If the numbers on the paperwork match the watch then that's a good stat, but by no mean infallible, so pictures are going to be needed.
Author:  what7 [ Fri Jun 05, 2020 5:16 am ]
Post subject:  Re: Would appreciate help with a steelfish
I tried to post pics but couldn't figure it out.
I saw the watch in person and was able to remove the back the movement was correct and it had all papers and the number on the movement case and papers matched. I am 100% sure its authentic.
However the crown dosent engage the movement it just spins and pulls out of the case when trying to switch between winding and date time setting.the watch works and the balance was spinning.
I am sure i can find a crown and that it can be repaired internally.but i do have a question on the crown tube.
Can the crown tube be replaced or is it integrated in the case?
Thanks for all your help!!!
Author:  bnewbie [ Fri Jun 05, 2020 5:18 am ]
Post subject:  Re: Would appreciate help with a steelfish
Crown tube is integrated.
Author:  what7 [ Fri Jun 05, 2020 5:22 am ]
Post subject:  Re: Would appreciate help with a steelfish
Thanks!
It screws down fine
Am i correct in assuming the tube is ok given that fact or could there be other issues? I dont want to go too deeply down the watch repair rabbit hole lol
Author:  Driver8 [ Fri Jun 05, 2020 5:45 am ]
Post subject:  Re: Would appreciate help with a steelfish
Adding pictures is very easy. This thread at the top of this sub-forum explains how -

viewtopic.php?f=1&t=66281
Author:  what7 [ Fri Jun 05, 2020 5:47 am ]
Post subject:  Re: Would appreciate help with a steelfish
Thanks
Author:  what7 [ Fri Jun 05, 2020 5:56 am ]
Post subject:  Re: Would appreciate help with a steelfish
Attachment:
20200605_065347.jpg


Ok i think i figured out the pics
Author:  bnewbie [ Fri Jun 05, 2020 6:08 am ]
Post subject:  Re: Would appreciate help with a steelfish
It is genuine.
Author:  usfelli2015 [ Mon Jun 22, 2020 3:26 pm ]
Post subject:  Re: Would appreciate help with a steelfish
You may have a serious problem with the crown stem not engaging. Breitling will probably insist on a complete service. $$$
Author:  MickeyWatch [ Sun Jun 28, 2020 7:11 am ]
Post subject:  Re: Would appreciate help with a steelfish
There is always a reason why anything is being sold at a "great price". Better do some research on service from Breitling...I'd add about $700-$850 to the purchase price and then confirm if it is a good deal.
Page 1 of 1 All times are UTC - 8 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/