The Breitling Watch Source Forums
https://www.breitlingsource.com/phpBB2/

Winding Specs for Avenger Skyland
https://www.breitlingsource.com/phpBB2/viewtopic.php?f=1&t=24120		 Page 1 of 1
Author:  cgl0ver226 [ Mon Nov 01, 2010 1:55 pm ]
Post subject:  Winding Specs for Avenger Skyland
I ordered an avenger skyland and was looking into getting a watch winder for watchwinderstore dot com... was just wondering what the specs were for winding the watch (clockwise, counter clock wise or alternate) don't know if it will say so in the manual since i haven't gotten the watch yet (a bit anxious i guess) also i ordered the diver proII strap with clasp as well as the metal bracelet and plan on changing the bands every now and then, is this something i can do at home easily (was thinking of buying the bergeon spring tool to do it myself so i don't have to go back and forth to the jewelry store and bother them everytime) thanks for any info as i am completely new to this
Author:  Roffensian [ Mon Nov 01, 2010 3:00 pm ]
Post subject:  Re: Winding Specs for Avenger Skyland
cgl0ver226 wrote:
I ordered an avenger skyland and was looking into getting a watch winder for watchwinderstore dot com... was just wondering what the specs were for winding the watch (clockwise, counter clock wise or alternate) don't know if it will say so in the manual since i haven't gotten the watch yet (a bit anxious i guess) also i ordered the diver proII strap with clasp as well as the metal bracelet and plan on changing the bands every now and then, is this something i can do at home easily (was thinking of buying the bergeon spring tool to do it myself so i don't have to go back and forth to the jewelry store and bother them everytime) thanks for any info as i am completely new to this



Everything you need to know about winders - viewtopic.php?f=6&t=23867
Author:  sharkman [ Mon Nov 01, 2010 3:31 pm ]
Post subject:  Re: Winding Specs for Avenger Skyland
Re strap changes - yes you can do it yourself. Just order a Bergeon 6767F spring bar tool. Get some extra tips with it. There is a video turorial on this site about changing from bracelet to strap. If you don't have any, you should get a couple screwdrivers for sizing the bracelet(or you could just spend $20 and have it done at most any jeweler, which might be a good idea with the rubber strap sizing if you have never done it before. If you do it yourself use a very sharp knife, cut straight down, and do it one section at a time, alternating sides. After each cut, put the strap back in the deployment and see where you are. The ends you will be cutting attach with regular spring bars to the inside of the clasp which is a tad difficult to see at first but by squeezing the strap you will be able to see the spring bars in the clasp.)
Author:  cgl0ver226 [ Mon Nov 01, 2010 4:33 pm ]
Post subject:  Re: Winding Specs for Avenger Skyland
WOW! thanks alot the winder thread was very helpful - everything i needed to know basically... as far as sizing the bracelet and bands i'm going to have the jewelry store do it and buy the bergeon to change bands.. thanks again
Author:  cgl0ver226 [ Thu Nov 11, 2010 5:24 am ]
Post subject:  Re: Winding Specs for Avenger Skyland
anyone know which size screwdriver to take the screws out of the polished bracelet?
Author:  Roffensian [ Thu Nov 11, 2010 5:35 am ]
Post subject:  Re: Winding Specs for Avenger Skyland
cgl0ver226 wrote:
anyone know which size screwdriver to take the screws out of the polished bracelet?



It's been a couple of weeks since I last said this, so we must be due......

Perfect size is 1.8mm, the Bergeon 180 is becoming almost impossible to find on its own so a Bergeon 160 (1.6mm) fits fine.
Author:  cgl0ver226 [ Thu Nov 11, 2010 4:34 pm ]
Post subject:  Re: Winding Specs for Avenger Skyland
just ordered a 1.6 on ebay -- not realizing after i paid and got my receipt saying it would take about 20 days (seller is from austrailia - great job by me!)
Page 1 of 1 All times are UTC - 8 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/